您好,欢迎来到本网站!江苏特昂机械集团有限天发国际娱乐,天發娱乐老虎机,天发娱乐场 专业销售:剪板机,折弯机和卷板机等产品

400-008-54880

关于特昂集团 | 设为首页 | 加入收藏
 
 

您现在所在位置:首页 > 天发国际娱乐

【 来源:原创 】 【 发布时间:2017-08-07 】 【 字体:
折弯机液压系统的故障有:阀不能换向或换向动作缓慢,泄漏,电磁先导阀有故障等。
Bending machine hydraulic system faults are: valve can not change or change the slow action, leakage, electromagnetic pilot valve failure, etc..
(1)换向阀不能换向或换向动作缓慢,一般是因润滑不良、弹簧被卡住或损坏、油污或杂质卡住滑动部门等原因引起的。对此,应先检查油雾器的工作是否正常;润滑油的粘度是否合适。而电路故障一般又分为控制电路故障和电磁线圈故障两类。在检查电路故障前,应先将换向阀的手动旋钮滚动几下,看换向阀在额定的气压下是否能正常换向,若能正常换向,则是电路有故障。此时,应更换密封圈、阀杆和阀座,或将换向阀换新。假如在额定电压下换向阀不能正常换向,则应检查电磁线圈的接头(插头)是否松动或接触不实。检查时,可用仪表丈量电磁线圈的电压,看是否达到了额定电压,假如电压过低,应进一步检查控制电路中的电源和相联系关系的行程开关电路。
(2) for a long time after the use of the valve spool valve sealing ring wear, stem and valve seat damage phenomenon, resulting in leakage of the valve, the valve action is slow or not normal commutation failure. At this point, the sealing ring should be replaced, the stem and the valve seat, or to replace the valve.
(3)若电磁先导阀的进、排气孔被油泥等杂物堵塞,封锁不严,流动铁芯被卡死,电路有故障等,均可导致换向阀不能正常换向。
(1) the reversing valve can not reverse or change the slow action, generally due to poor lubrication, the spring is stuck or damaged, oil or impurities stuck sliding part and other reasons. In this regard, we should first check the oil mist is working properly; the viscosity of the oil is suitable. If necessary, replace the lubricating oil, clean the sliding part of the valve, or replace the spring and the valve.
(2)换向阀经长时间使用后易泛起阀芯密封圈磨损、阀杆和阀座损伤的现象,导致阀内泄漏,阀的动作缓慢或不能正常换向等故障。对前3种情况应清洗先导阀及流动铁芯上的油泥和杂质。
(3) if the solenoid pilot valve into the exhaust hole blocked by sludge and other debris, not tightly closed, the movable iron core clamping circuit failure, which can lead to the valve does not change. The pilot valve should be cleaned and the activity of sludge and impurities on the core of the former 3 cases. The circuit fault is generally divided into two types of control circuit fault and electromagnetic coil fault. Before checking the circuit fault, the valve should be turned on the manual knob several times, to see whether the nominal pressure of the valve can be normally reversed, if the normal commutation, the circuit is faulty. When the inspection, the instrument can be used to measure the voltage of the electromagnetic coil, to see whether the rated voltage, if the voltage is too low, it should be further check the power supply in the control circuit and the associated trip switch circuit. If the rated voltage of the valve can not be normal commutation, it should check the electromagnetic coil connector (plug) is loose or contact is not real. Method is to pull the plug, measure the coil resistance, if the resistance is too large or too small, indicating that the electromagnetic coil is damaged, should be replaced.。必要时,应更换润滑油,清洗换向阀的滑动部门,或更换弹簧和换向阀。方法是,拔下插头,丈量线圈的阻值,假如阻值太大或太小,说明电磁线圈已损坏,应更换。
添加时间:2017-08-07  浏览次数:0
 下一个:折弯机PLC的分类



地址:江苏 · 海安 · 南海大道11号
服务热线:400-008-5488
电话:0513-81857188
手机:(0)18662926888
传真:0513-81857166
集团简介 业务概览 财务摘要 集团新闻 售后服务 技术实力
董事长致辞 产品及服务 公告及通函 网站公告 服务理念 技术成果
企业文化 基地及设施 财务报告 媒体查询 服务网络
企业里程碑 科研发展 招股书   服务热线
发展目标 销售网络 演示材料    
集团架构 竞争优势 经营成果展    
质量方针 增长亮点 投资者查询    
天发国际娱乐,天發娱乐老虎机,天发娱乐场资料 特昂价值观 投资者意见      
团队风采        
人文特昂     版权所有 江苏特昂机械集团有限天发国际娱乐,天發娱乐老虎机,天发娱乐场 后台管理